Vacuum-compatible, 25.4-mm mirror mount, stainless steel, high-stability, front-loading, 3 hex adjusters
VMHX-25.4F
VMHX-series mounts are all-stainless steel, vacuum compatible mounts. To minimize the outgassing, special cleaning, along with vacuum grease and vented holes are provided. BARRIERTA SUPER IS/V vacuum grease is used. The MHX mounts feature a hollow-frame design that not only provides a higher moment of inertia to maximize stiffness but also thinner, reduced-mass sections allowing it to reach thermal equilibrium faster than traditionally designed mounts. Thermal repeatability tests validate the effectiveness of the new frame design, showing lower deflection and equivalent repeatability against rival mounts. The MHX mount is loaded with additional features like center-post mounting, adhesive wells, and keying pin slots, all in the industrys most compact and affordable stainless steel mount. Ideal for interference measurement or precision measurement.
◦ To minimize the outgassing, venting hole and grooving are provided onto screw holes and inset sections.
◦ BARRIERTA SUPER IS/V grease is used for sliding part. ◦In the case of MHX-25.4F-R, Insert the mirror from the back and fix it when the mirror's reflective surface hits the mirror frame . As a result, the mounting center of the rod and the reflecting surface of the mirror can always be matched even if the thickness of the mirror changes.
◦MHX-25.4F/F-R has three adjustment screws to adjust not only tilt and rotation but also reflective surface the back and forth. The MHX-25.4A has only two adjustment screws to adjust only tilt and rotation.
◦Equipped with bonding holes for mirror bonding and pin holes for rotation prevention and positioning.
◦High-density stainless steel is used for the material, but the weight has been reduced by reducing the thickness.
◦The thickness of the frame is made thinner and follows immediately even if the temperature changes, and the distortion of the frame due to the temperature distribution is kept low.
◦ BARRIERTA SUPER IS/V grease is used for sliding part. ◦In the case of MHX-25.4F-R, Insert the mirror from the back and fix it when the mirror's reflective surface hits the mirror frame . As a result, the mounting center of the rod and the reflecting surface of the mirror can always be matched even if the thickness of the mirror changes.
◦MHX-25.4F/F-R has three adjustment screws to adjust not only tilt and rotation but also reflective surface the back and forth. The MHX-25.4A has only two adjustment screws to adjust only tilt and rotation.
◦Equipped with bonding holes for mirror bonding and pin holes for rotation prevention and positioning.
◦High-density stainless steel is used for the material, but the weight has been reduced by reducing the thickness.
◦The thickness of the frame is made thinner and follows immediately even if the temperature changes, and the distortion of the frame due to the temperature distribution is kept low.
| Name | Vacuum-compatible, 25.4-mm mirror mount, stainless steel, high-stability, front-loading, 3 hex adjusters |
|---|---|
| Weight | 0.1700kgs |
| Guide |
|
| Attention |
|
| Optic Loading Side | Front Loading |
| Angle Range | ±3° |
| Material | Stainless Steel |
| Number of Control Axes | 3 Axes |
| Optic Diameter | φ25.4mm |
| Compatible Optics Thickness | 3 - 7mm |
| Mirror Clamping Mechanism | Set Screw with Torsion Barrier, 2-mm (5/64-in.) Hex Key |
| Recommended Mirror Clamping Torque | 0.07+/-0.01 Nm (10+/-2 oz.-in.) |
| Number of Adjustment Axes | 3 points |
| Angular Travel Range | +/-3deg. |
| Linear Travel Range | +/-3.5mm |
| Adjuster Thread | M6 x 0.250mm(~100 TPI) |
| Standardized Adjustment Sensitivity (based on 1deg. knob rotation) | 20 urad |
| Typical Adjustment Sensitivity | 6+/-2 urad |
| Dowel Pin Keys | 2mm Slot and Hole |
| Standard Mounting | Counterbored clearance hole for M4 / 8-32 screws |
| Center-Post Mounting | M4 and 8-32 threaded holes |
| Thermal Repeatability with a 10deg.C Thermal Cycle | 1.5 urad |
Out of stock
SKU
VMHX-25.4F
$327.00
Customize product
VMHX-series mounts are all-stainless steel, vacuum compatible mounts. To minimize the outgassing, special cleaning, along with vacuum grease and vented holes are provided. BARRIERTA SUPER IS/V vacuum grease is used. The MHX mounts feature a hollow-frame design that not only provides a higher moment of inertia to maximize stiffness but also thinner, reduced-mass sections allowing it to reach thermal equilibrium faster than traditionally designed mounts. Thermal repeatability tests validate the effectiveness of the new frame design, showing lower deflection and equivalent repeatability against rival mounts. The MHX mount is loaded with additional features like center-post mounting, adhesive wells, and keying pin slots, all in the industrys most compact and affordable stainless steel mount. Ideal for interference measurement or precision measurement.
Resources & Downloads
Related Products
Check items to add to the cart or
